HP EliteBook 2170p


Return to index

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING, OR YOU MIGHT BRICK YOUR MACHINE: SAFETY PRECAUTIONS

HP EliteBook 2170p
Specifications
Manufacturer HP
Name EliteBook 2170p
Variants EliteBook 2170p
Released 2012
Chipset Intel QM77
CPU Intel Ivy Bridge ULV
Graphics Intel HD Graphics 4000
Display 1366x768 11.6" TFT
Memory Two slots, max 8GB/slot (2x16GB), DDR3/sodimm
Architecture x86_64
EC SMSC KBC1126, proprietary (in main boot flash)
Original boot firmware HP UEFI firmware
Intel ME/AMD PSP Present. Can be disabled with me_cleaner.
Flash chip SOIC-8 16MiB (128Mbit), in a socket
W+: Works without blobs; 
N: Doesn't work; 
W*: Works with blobs; 
U: Untested; 
P+: Partially works; 
P*: Partially works with blobs
Features
Internal flashing with original boot firmware N
Display (if Intel GPU) W+
Audio W+
RAM Init W+
External output W+
Display brightness W+
Payloads supported
GRUB Works
SeaBIOS Works
SeaBIOS with GRUB Works

Introduction

This is a portable, 11.6" Ivy Bridge platform from HP. More information is available on the coreboot documentation - that page said (on 16 August 2023) that GRUB hangs due to the at_keyboard module, but this is no longer true; it’s fixed in the latest GRUB revisions, and Libreboot’s version of GRUB contains this fix.

Unavailable in Libreboot 20230625 or earlier. You must compile from source, or use at least Libreboot 20231021.

Build ROM image from source

The build target, when building from source, is thus:

./mk -b coreboot hp2170p_16mb

Installation

Insert binary files

If you’re using a release ROM, please ensure that you’ve inserted extra firmware required refer to the guide for that. (failure to adhere to this advice will result in a bricked machine)

Set MAC address

This platform uses an Intel Flash Descriptor, and defines an Intel GbE NVM region. As such, release/build ROMs will contain the same MAC address. To change the MAC address, please read nvmutil documentation.

Flash a ROM image (software)

If you’re already running Libreboot, and you don’t have flash protection turned on, internal flashing is possible.

Flash a ROM image (hardware)

REMOVE all power sources like battery, charger and so on, before doing this. This is to prevent short circuiting and power surges while flashing; although the flash is socketed, hot-swapping is generally a bad practise and must be avoided.

Otherwise, external flashing is simple, but quite different from most laptops! The flash is a SOIC8 IC like you’d expect, but it’s in a socket.

Remove those two screws and cover on the underside, and then the flash is in this socket which you can open:

For general information, please refer to 25xx NOR flash instructions - that page refers to use of socketed flash.

For this board, you can use a Raspberry Pi or similar flasher if you wish, wired to a spring socket adapter (SOP to DIP adapter) in a breadboard. In my case, I opted for use of a 3.3v-modded CH341A device.

Here, the flash is inserted into the SOP to DIP adapter, which is then put into the ZIF socket on the CH341a device. This is the black version which has 5V logic levels, but it can (read: MUST) be modified for correct 3.3v logic levels. The main 25xx flashing guide documents this; some other models may already be 3.3v, or have switchable logic levels like on some newer revisions of CH341A. Please ensure that you run it at the correct voltage.

HP EliteBook 2170p success

Markdown file for this page: https://libreboot.org/docs/install/hp2170p.md

Subscribe to RSS for this site

Site map

This HTML page was generated by the Untitled Static Site Generator.